Clean, adjusted and gliding in about 10 minutes, for many doors. $12.
You fight it every time you open it, and every push grinds the rollers and the track down a little more. Most of the time it isn’t the door: it’s a dirty track or worn rollers. The kit’s 2-minute check tells you which. A clean, lubricated and adjusted door often slides like new; if the rollers are gone, the kit shows how to measure yours, which to buy and the swap.
★★★★★161 Google reviews · From Mr Door Pro, Orlando · It glides again, or your money back
From Mr Door Pro. By email right after you pay: the steps, the videos and your photo assistant.
$12 is less than one good roller ($25 to $40). A Mr Door Pro visit starts at $120, and a new sliding door costs $3,000 to $6,000.
Secure payment by Stripe · Your kit arrives by email right after you pay · 30-day money-back guarantee
Open and close it slowly, a flashlight along the track, the gap at the frame, the bottom of the panel. A table sends you to the fix.
The $2 steel wire brush we use on our own jobs, a vacuum and degreaser. For many doors that’s all it takes.
Silicone, a two-second burst per rail, or nothing at all. Never WD-40, oil or grease: they hold sand and grind the rollers down.
A quarter turn at a time, until the panel clears the track and the gap at the frame is even.
Plastic guides on top that rub the head track: take them off or shave them, and keep spray off them.
How to tell, how to measure the old one and which to buy, and the swap with the panel standing in its track. The videos show us doing it.
I’m Davi. I own Mr Door Pro, and fixing sliding doors is all we do. Every step in this kit is how we do it on real jobs, written down for one job: a sliding door that’s hard to open.
“Davi did a great job fixing the sliding door that had bugged my wife for the last 4yrs. Quick service, reasonable prices. Would recommend.”Aaron W. · Google review
“I got an appointment for an estimate right away and they were able to fix my door at the same time. Davi was prompt, efficient and pleasant.”Tracy M. · Google review
Real reviews of Mr Door Pro on Google: 161 reviews, 5.0 rating.
If your door still sticks after you follow the kit, write to us within 30 days and we refund every dollar.
Near Orlando? We come and fix it: free estimate at your home.
A $2 steel wire brush, a vacuum and degreaser for the track, and a screwdriver to adjust the rollers. For a roller swap: screwdrivers, pliers, a stiff putty knife, a rubber mallet and a short piece of 2x4. The kit lists every one.
The check takes 2 minutes and each fix about ten. If the rollers are gone, plan half a day: our technicians take about two hours per panel.
Most people have. It can get a stuck door moving for a day, then it works like glue and holds the sand. Clean it all out of the track and off the rollers first: the kit shows how.
If you have to lift the door to make it slide, if the panel almost touches the track, or if an adjustment screw turns and nothing moves, the rollers are worn. The kit’s check tells you.
Measure the old one the way the kit shows: housing size, wheel size and material, grooved or flat edge, one or two wheels, where the screw goes. Send the photos to your assistant. Still not sure? Reply to your kit’s email and we tell you exactly which one to buy.
If your door still sticks after you follow the kit, write to us within 30 days and we refund every dollar. Near Orlando? We come and fix it: free estimate at your home.
Those panels are much heavier, and their rollers usually come out with the panel, with two people and glass suction lifters. For most people it is a job for a pro. Send your assistant a photo first.
No subscription: $12, one payment. Right after you pay, an email arrives from diy@mrdoorpro.com with the kit as a PDF and the link to your videos and your photo assistant.
$12, one time. It glides again, or your money back.
Get the kit · $12